PYLE Audio TV Mount PSWLE56 User Guide

INSTALLATION GUIDE  
Item No.:PSWLE56  
Thank you for choosing our product  
Pyle Audio  
1600 63rd st , Brooklyn, NY, 11204  
(718)236-8000  
TV Size Range: 23"~46"  
Maximum Weight Capacity: 30kg/66lbs  
Locked by safety bolt on the bottom  
Balance adjust system is included  
Warning  
This product contains small items that could be a choking hazard if swallowed. Keep  
these items away from young children!  
1.Make sure these instructions are read and completely understood before attempting  
installation. If you are unsure of any part of this installation, contact a professional  
installer for assistance.  
www.pyleaudio.com  
CAUTION  
2.The wall or mounting surface must be capable of supporting the combined weight of  
the mount and the display; otherwise the structure must be reinforced.  
3.Safety gear and proper tools must be used. A minimum of two people are required  
for this installation. Failure to use safety gear can result in property damage, serious  
injury or death.  
This product was designed to be installed on wood stud walls and solid concrete walls.  
Before installing make sure the supporting surface will support the combined load of the  
equipment and hardware. Never exceed the Maximum Load Capacity. This product is  
intended for indoor use only. Use of this product outdoors could lead to product failure or  
personal injury.  
-8-  
 
Part 1aa-Wood SStud Moouunting  
Part 2bb-Attaacching brracketts to scrreen wiith reccessed back  
Use wall plate as a template, make sure it is level, and mark mounting holes  
along the center lines of the wood studs. Drill 3/16(5mm)dia.holes 2”  
(50mm) deep. Level wall plate and attach to wall with long bolts(J) and  
washers(L). Tighten screws firmly. Do not overtighten.  
Center brackets vertically on back of screen. Select the medium(F or G) or  
large(H) screws. Attach brackets to screen using four selected screws,four  
square washers(I) and four spacers(M) at the top and bottom of each bracket.  
Tighten screws firmly. Do not overtighten.  
Square washer(I)  
2(50mm)  
Large hole for  
M8 screws  
Φ3/16(5mm)  
Medium hole for  
M5 and M6 screws  
M
F-H  
I
Wood stud  
Bubble level  
L
J
-3-  
-6-  
 
Part 1b--Concrette Wall MMoounting  
Part 2aa-Attaachingg Brackeets To SScreenn WWith Fllat Back  
Level wall plate and use it as a template to mark holes. Drill 3/8(10mm) dia.  
holes 2(50mm) deep. Insert anchors(K) into holes and secure wall plate  
with long bolts(J) and washers(L). Tighten screws firmly. Do not overtighten.  
Center brackets vertically on back of screen. Select the small(A or B),medium  
(C or D) or large(E) screws. Attach brackets to screen using four selected  
screws and four square washers(I) at the top and bottomof each bracket.  
Tighten screws firmly. Do not overtighten.  
Square washer(I)  
2(50mm)  
Large hole for  
M8 screws  
Φ3/8(10mm)  
Medium hole for  
M5 and M6 screws  
Small hole for  
M4 screws  
A-E  
I
Concrete Wall  
K
L
Bubble level  
J
-5-  
-4-  
 

RCA Handheld TV E13700 User Guide
Regency Indoor Fireplace L676 User Guide
Rheem Water Heater 92 103234 02 User Guide
Ricoh Printer Aficio 3228C User Guide
Ricoh Scanner 337943 003 User Guide
Russell Hobbs Appliance Trim Kit RHM1709 G User Guide
Ryobi Chainsaw P545 User Guide
Samsung Computer Hardware DDR3 User Guide
Samsung Projection Television ST42W5P User Guide
Sears Carpet Cleaner 175 User Guide